Although installing a slide parts kit on a Glock 19 or Glock 17 may appear difficult, anybody can do it with the correct knowledge. These days, gun owners are more interested in keeping their guns updated and in good working order from the comfort of their own homes.
Our Glock guns specialists at 3CR Tactical are skilled in the efficient disassembly of their sidearm. They provide all the necessary information to build your Glock in this page.
Brief overview of GLOCK G19 slide assembly
The GLOCK 19 slide assembly is a crucial component of the G19 pistol. It is known for its compact size and reliability. Here’s a brief overview of the G19 slide assembly:
Slide: The slide is the upper a part of the pistol. It houses the barrel and cringe spring meeting. The slide typically consists of serrations for less complicated manipulation. Also, it has a rear sight, and the front sight to aim comfortably.
Barrel: The barrel is housed in the slide. This barrel is responsible for guiding the bullet out of the chamber and down the barrel in the course of firing. Also, GLOCK barrels are known for its durability and accuracy.
Recoil Spring Assembly: This meeting enables control the drawback of the pistol after firing. It consists of a flinch spring and a guide rod. This guide rod paints together to soak up and redirect the strength from the fired spherical.
Sights: The G19 slide assembly usually comes with constant attractions. It should have aftermarket alternatives for adjustable sights. These points of interest useful resource in aiming the pistol appropriately.
Slide Stop Lever: The slide stop lever is a small element that holds the slide open just after the last round is fired.
Extractor and Ejector: These components paintings together to extract spent casings from the chamber. They also eject them from the pistol in the course of the slide cycling.
Finish: GLOCK slides are commonly completed with a long lasting coating inclusive of Tenifer. This Tenifer offers corrosion resistance and enhances the slide’s longevity.
What are Stripped and Completed Glock Slides?
When searching for a slide for a Polymer80 or Glock construction, you have undoubtedly seen terms like “complete” or “stripped/bare.” When all of the primary parts of a slide are installed or included and ready to be placed on the frame, the slide is deemed “complete.”
When the main slide is supplied without the internal components, barrel, or sights attached, it is referred to as “stripped.” In the event that you purchase a stripped slide, you will want a corresponding components kit in order to assemble it.
Necessary Tools required for assembly
When it comes to assembly work, the necessary tools can vary depending on the specific task and materials involved. However, here’s a general list of tools that are commonly needed for assembly:
Screwdrivers: Flathead and Phillips head screwdrivers are needed to tighten or loosen a screwdriver.
Hammer: Used to move nails or tap parts into position.
Pliers: Useful for twisting, bending or cutting wires and small objects.
Wrenches: For fastening poles and cables, an adjustable wrench or socket wrench is required.
Allen Keys/Hex Keys: These are needed to assemble furniture and other items that use square socket screws.
Electric drill: Helps drill holes, driving screws, and other energy-intensive tasks.
Level: Ensures that assembled parts are straight and properly aligned.
Tape Measure: Used to measure distance during assembly and ensure accuracy.
Utility Knife: Useful for cutting and cutting materials such as plastic, paper, or packaging.
Safety Equipment: Safety glasses, gloves and ear protection may be required depending on the job.
Assembly Instructions: Although not a tool, it is important to have clear and detailed assembly instructions specific to the item being assembled.
How to Assemble a GLOCK G19 Slide?
Installing the Lower Parts Kit on an AR requires more work than building out a slide. But remember, you’re still working with tiny, spring-loaded parts, so have a plastic bag on hand.
You may avoid a lot of trouble if you install the plunger in a plastic bag in case you lose your hold and the plunger top shoots out. When you and your parts are prepared, do the following:
The Firing Pin should be placed in its polymer retainer.
Over the firing pin, slide the spring.
Position the two retention clips while maintaining pressure on the Spring. With this, the Striker Assembly is finished.
In the Firing Pin Safety, insert one of the little springs.
Attach the second little spring to the extractor’s guiding rod.
Put the spring-loaded bearing on the safety plunger assembly’s open end. Press the bearing firmly against a hard surface to seat it.
Seat the Firing Pin Channel Liner firmly yet gently into place with your installation tool. Avoid forcing it in as this may cup the ends and prevent the striker assembly from moving as intended.
Put the firing pin safety in place.
After releasing the firing pin safety, lower the extractor into position.
Position the extractor plunger assembly by dropping it in.
Place the Striker Assembly in position while maintaining pressure on the Firing Pin Safety.
To secure the rear plate in place, use a tiny punch to compress the firing pin retainer. As you move the punch to the spring-loaded bearing, seat the back plate at the same time by depressing it. To completely seat, it might be necessary to tap in new plates.
Install the assembly of the recoil spring and barrel.
Slide your finished Glock 17 or Glock 19 onto it.
Testing and Function Check of G19 slide
Testing and function checking a Glock G19 slide involves several steps. These steps ensure its proper operation and safety. Here’s a general outline of what you might do:
Verifying slide movement and safety features:
Mandatory point: Always point the gun in a safe direction.
Verify that the ammunition is unloaded by thorough visual. Also, you should inspect physically the chamber and magazine.
Inspect firing pin and firing pin protection for wear or damage.
Make sure the slide stop/release engages and slides securely.
Check extractor and extractor alignment and proper operation.
If the gun was disassembled for inspection, reassemble it.
Perform a final inspection of all safety features, including trigger safety and landing safety.
Performing a function test after assembly:
With the slide in the frame, rotate the slide by hand to check for proper operation.
You must ensure that the magazine closes the slide securely when empty.
Check that the extractor is working properly by inserting an empty case or snap cap and cycling the slide on.
Check and reset the trigger pull to ensure proper operation.
Make sure all external components such as sights and slide serrations are in good condition.
Final Steps
You will also need to install your sights. Or, you can also have a gunsmith install them for you. It is recommended if you are new or not sure whether it is properly installed.
Every slide has the capacity to hold every component that are needed to create a whole slide assembly. When you buy a whole slide kit from MidStateFireArms, they always take care of the installation.
Importance of regular maintenance for firearm longevity
Regular maintenance is necessary to ensure the durability and reliability of firearms including the Glock 19.
Accurate Preservation:
It is good to clean and maintain the barrel and other components. This can help you safeguard the long-term accuracy and stability of your Glock 19.
Troubleshooting:
Proactive maintenance and repairs can prevent malfunctions. Therefore, you must focus on regular cleaning and inspection. Staying active in maintaining can help identify and address trivial and non-trivial issues and potential problems of the future.
Safety:
Proper firearms maintenance goes hand-in-hand with safety. A clean and well-maintained Glock 19 is less prone to failures or unexpected accidents.
Resale Value:
Taking care of your Glock 19 doesn’t just benefit you today, but also helps in the future. A well-maintained firearm holds its resale value much better than a neglected one.
Discussion about this post